![]() If you have no time and expertise and do nothing else, run the track through the compressor (Effect -> Compressor and accept the defaults.). There are many mastering tutorials out there, but here’s the cut down version. Mastering is something you do to finished tracks, and it’s a combination of art and science. This is to remind you this is not a mastered track (Don’t save mixes as MP3 at this stage you want to preserve quality until after you’ve mastered the track.). Then mix down all your separate tracks into a stereo track by exporting it as a WAV or AIFF uncompressed file with the words RAW at the end of the filename. When you are finished, once again, save it first as a AUP project to save your track work. Then select all and use the Time Shift tool to slide all the trimmed tracks to the beginning. Do this for each track so you remove any lead ins and lead outs. This removes everything either side of the bit you want to keep. To trim all the tracks down to the same size (because it can get a little messy), select the usable area of the track, removing any count in and messy tail bits, Perhaps do a countdown on one the first tracks to help you sync it. It’s a good idea to leave a little bit of time at the beginning so you can start playing along as the other tracks start. It makes the mix more spacious and allows certain instruments to come through if they’re not competing directly for space with another.įor each new track, just press Record and start playing. See how it affects your mix if you move things around left and right. Just try to make all the tracks sit together well in the mix.ĭon’t forget to also pan the tracks around in the stereo spectrum, unless of course you are making mono music (who does that intentionally?). It’s a common rookie mistake to try and mix a finished track, but that’s not how it’s done. When balancing each track against each other, concentrate on just blending the tracks together without any record to overall loudness. You don’t have faders, just volume controls at the front of each track in the track control panel. Mixing in Audacity is less easy and intuitive than it is in a proper DAW program. If you export you will smush the tracks into a single track and lose all your separate tracks. When you are done recording tracks, save as an AUP Project (not via an exported file). You can manually align tracks and improve the timing by sliding them left and right. You can also adjust the alignment of the tracks with the “Time Shift” tool – the little button next to the magnifying glass with the back and forth arrows. If you are using a hardware I/O box, the latency will be much reduced, but you can tweak it in the Preferences above reducing the latency and latency correction until it can go no lower without dropping out (For more about latency see our article about it here.) You may find that synchronization goes out of whack along the way. The hardware and software playthrough may improve the synchronization if your machine has an I/O box or is fast enough to support it. ![]() ![]() To listen to previous tracks while recording, go to the Preferences, on “program menu -> Preferences -> Recording,” check the radio buttons for “Overdub: Play other tracks while recording new ones” in the playthrough section. To record more tracks you have to make sure that you can hear the other tracks while recording. When you render and mix the track you can mute the click track by clicking the mute button in the track’s control panel. Just choose “Generate -> Click Track” and input the tempo of your piece. ![]() It’s a good idea to either use a click track or lay the drums down first to give subsequent tracks a rhythm to play to. The music records into the track, and when you’re done you simply press stop. You connect a microphone to your computer and click Record on the Audacity interface. Recording or tracking your music in Audacity is easy enough. Tip: Improve your workflows by using these Audacity keyboard shortcuts. In this article we will talk about how to use Audacity as a multitrack studio and making finished tracks using all the little tricks which make it easy. With it you can convert different sound formats and also record music and master it for finished professional music and sound design. It’s a professional quality sound wave editor which a lot of people use because it’s free and it’s good. But you may already have something you can use for multitrack music already installed on your system and not even know it.Īlthough it’s not really made for the purpose, and it’s less like a DAW and more like and old 8-track Portastudio, you can record multiple tracks on the open-source cross-platform sound editor Audacity. Digital Audio Workstation (DAW) software can be expensive and sometimes this can stand in the way of musicians who want to record and mix multitrack music. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |